SPTA USA · BUYING GUIDE

Choose the right polishing pad.

Choose by size, material and cutting strength—then find the right SPTA pad for your paint, machine and detailing job.

THE THREE-STEP CHECK

Make the right choice, in three steps.

01

Match the size

Use a pad designed for your backing plate and tool. Check the product's actual diameter and attachment type—not just the machine's advertised size.

Check backing plates ↗
02

Choose the material

Foam covers cutting through finishing; wool is often used for stronger initial correction. Microfiber can be cutting or finishing depending on the specific pad. Compare the grade, face design, and suitable machine before choosing.

See material recommendations ↗
03

Choose the cut

For light swirls, try medium-cut foam on a test spot. For final gloss, use a finishing pad. Use heavy-cut pads only when the surface needs stronger correction.

Compare cut grades ↗
Important: pad colors aren't universal. In SPTA's FF/SF foam series, orange means heavy cut, blue means medium cut, and gray means finishing. The T-series has a different progression—its orange T40 is light cut. Always check the pad series and listed cut grade.
COLOR & CUT REFERENCE

Two systems. Two different color charts.

Do not substitute a color from one series for the same color in another.

FF & SF foam pads

Three-stage progression for flat-face and square-face foam pads.

Orange Heavy cut Shop ↗
Blue Medium cut Shop ↗
Gray Fine finish Shop ↗
Browse foam polishing pads ↗

T-series foam pads

Use the T-number and cut-grade description, not color alone.

Green T120 Heavy cut Shop ↗
Yellow T80 High cut Shop ↗
Blue T60 Moderate cut Shop ↗
Orange T40 Light cut Shop ↗
Red T10 Ultra-fine finish Shop ↗
Browse foam polishing pads ↗
PAD CONSTRUCTION

Flat-face or square-face foam?

FF and SF describe pad face construction, not a new color-cut system. Compare the two surfaces and choose the appropriate size and cut grade.

SHOP BY THE JOB

A simpler starting point.

These examples are U.S. product listings. Choose a size that fits your specific backing plate, and confirm your pad-and-compound combination on a test area. Availability and prices are shown from Shopify.

01 / START HERE

First time polishing? Start with medium cut and finishing.

Blue FF foam offers medium correction; gray FF foam can refine light defects and improve gloss. Start with a small test spot and the least aggressive combination that produces the result you need.

02 / STRONGER CORRECTION

For heavier defects, choose an appropriate cutting pad.

Orange FF foam and heavy-cut wool provide more aggressive options. Follow with medium-cut or finishing stages as the paint requires. Deep defects may not be safely removable by polishing.

03 / SPECIALIZED WORK

Working in tight areas or looking for finishing alternatives?

Mini foam pads help reach smaller areas when correctly paired with a suitable mini backing system. Microfiber finishing pads are another option; microfiber doesn't automatically mean heavy cutting.

MANUFACTURER APPLICATION REFERENCE

Understand where each tool fits.

The manufacturer reference shows overlapping ranges for sanding, compounds, pad materials and polishers. Read these as approximate application areas, not exact cut ratings, material-removal measurements or pad-fit approvals.

Grinding / sanding

Deep defects and sanding marks; specialized paint-leveling work, not a routine starting step.

Heavy cut

Stronger correction for substantial, safely correctable scratches and oxidation.

Medium cut

Moderate scratches, swirls and residual cutting marks.

Light cut

Fine wash marks, minor haze and surface refinement.

Finish

Gloss enhancement and final refinement of fine marring.

Tool / consumableGrindingHeavy cutMedium cutLight cutFinish
Sanding & grinding
1200/1500-grit sandpaper Sanding application; professional assessment required Approximate manufacturer application range for 1200/1500-grit sandpaper, shown across the correction stages. Not a compatibility guarantee.
2000/3000-grit sandpaper Sanding / refining; not ordinary beginner polishing Approximate manufacturer application range for 2000/3000-grit sandpaper, shown across the correction stages. Not a compatibility guarantee.
Grinding / sander Manufacturer tool category Approximate manufacturer application range for Grinding / sander, shown across the correction stages. Not a compatibility guarantee.
Polishing compounds
Heavy-cut polishing compound General manufacturer category, not a specific USA SKU Approximate manufacturer application range for Heavy-cut polishing compound, shown across the correction stages. Not a compatibility guarantee.
Medium-cut polishing compound Broad correction-to-refinement range Approximate manufacturer application range for Medium-cut polishing compound, shown across the correction stages. Not a compatibility guarantee.
Finish polishing compound Refining to finishing range Approximate manufacturer application range for Finish polishing compound, shown across the correction stages. Not a compatibility guarantee.
Wool pads
Long-hair wool pad (reference A) First of two similarly labeled manufacturer rows; model unidentified Approximate manufacturer application range for Long-hair wool pad (reference A), shown across the correction stages. Not a compatibility guarantee.
Short-hair wool pad Manufacturer's short-nap category Approximate manufacturer application range for Short-hair wool pad, shown across the correction stages. Not a compatibility guarantee.
Long-hair wool pad (reference B) Second similarly labeled row; distinct bar, model unidentified Approximate manufacturer application range for Long-hair wool pad (reference B), shown across the correction stages. Not a compatibility guarantee.
Foam pads
Heavy-cut foam pad Cutting through moderate correction Approximate manufacturer application range for Heavy-cut foam pad, shown across the correction stages. Not a compatibility guarantee.
Light-cut foam pad Overlaps stronger and medium correction on original chart Approximate manufacturer application range for Light-cut foam pad, shown across the correction stages. Not a compatibility guarantee.
Medium-cut foam pad Correction through light-cut stage Approximate manufacturer application range for Medium-cut foam pad, shown across the correction stages. Not a compatibility guarantee.
Finishing foam pad Refinement through final gloss Approximate manufacturer application range for Finishing foam pad, shown across the correction stages. Not a compatibility guarantee.
Microfiber pads
Orange/white microfiber pad Manufacturer color description; U.S. SKU not verified Approximate manufacturer application range for Orange/white microfiber pad, shown across the correction stages. Not a compatibility guarantee.
White microfiber pad Refinement and finishing; U.S. SKU not verified Approximate manufacturer application range for White microfiber pad, shown across the correction stages. Not a compatibility guarantee.
Polishing machines
Rotary polisher Broad application range, not a pad-fit guarantee Approximate manufacturer application range for Rotary polisher, shown across the correction stages. Not a compatibility guarantee.
21 mm dual-action polisher Manufacturer range; machine selection differs by task Approximate manufacturer application range for 21 mm dual-action polisher, shown across the correction stages. Not a compatibility guarantee.
15/12 mm dual-action polisher Manufacturer range; exact model compatibility not implied Approximate manufacturer application range for 15/12 mm dual-action polisher, shown across the correction stages. Not a compatibility guarantee.
9 mm dual-action polisher Manufacturer range begins later in cutting progression Approximate manufacturer application range for 9 mm dual-action polisher, shown across the correction stages. Not a compatibility guarantee.

Adapted from the supplied SPTA Polishing Tool Application Chart. Bar endpoints are visually estimated from the graphic and are not measured performance data. Its repeated long-hair wool labels and microfiber color descriptions are retained without assigning U.S. SKUs. Paint depth, test-spot results, tool choice and technique determine the safe process. Sanding can permanently remove clear coat; never assume that a deep scratch is safe to eliminate.

How many polishing stages do you need?

A test spot determines whether one, two or more stages are justified. The examples below are practical starting points, not mandatory processes.

Finishing-only pass

For relatively clean paint or faint haze, a suitable finishing pad and polish may be enough. Confirm with a test spot.

Medium cut → finishing

A practical route for moderate wash marks and swirls: test medium-cut foam first, then refine the finish if needed.

Heavy → medium → finishing

A possible route for substantial correctable defects, but only where paint condition supports it. Aggressive correction is not automatically safe or necessary.

KEEP YOUR PADS WORKING

Plan for cleaning and replacements.

Having a clean spare pad can be more useful than forcing a loaded pad through the entire job.

While polishing

Inspect and clean the working face regularly. If the pad becomes heavily loaded with spent compound or residue, switch to a clean one.

After the job

Follow the pad maker's cleaning instructions, rinse out compatible cleaning products thoroughly, and let pads dry before storage.

When to replace

Retire torn or crumbling foam, failing hook-and-loop backing, or pads that no longer clean properly. For larger jobs, a practical planning estimate is 1–2 pads per stage when cleaning during work, or 3–4 if swapping loaded pads for later cleaning; actual needs vary by vehicle and conditions.

Explore Polishing Pad Cleaner ↗
QUESTIONS & SOLUTIONS

Troubleshooting & Frequently Asked Questions

Find answers to common pad-selection questions, compatibility issues, and troubleshooting. Expand any topic for details.

Choose by the job, not the color

Begin with the least aggressive pad-and-compound combination that can achieve the correction you need. Test a small, inconspicuous area first and adjust only if necessary. Color meaning changes across pad series.

Foam pad materials and face profiles

Foam comes in grades for cutting, polishing and finishing. Flat-face and square-face styles have different face profiles; select a suitable grade and size for your polisher and paint, and keep separate pads for different compounds.

Wool pads and stronger correction

Wool provides more aggressive options for heavy defect removal, but it may need a refining stage. It is not automatically appropriate for every finish. Check your machine and backing plate before choosing a wool pad.

Microfiber: cutting or finishing?

Microfiber is not always a cutting pad. SPTA offers products such as T100 cutting microfiber and T20 finishing microfiber. Compare their stated intended use rather than assuming a common grade.

Match pad diameter and attachment

Pad diameter isn't the same as backing plate diameter. Verify the supported plate and pad sizes and the hook-and-loop or threaded attachment. Approximately 1–2 inches is useful for tight spots, 3 inches for smaller panels, and 5–6 inches for larger panels when compatible.

Compounds and correction

Pair cutting pads with suitable heavier-grade compounds only when needed; follow with medium or finishing products as the paint requires. Compound grit ranges are intended-use indications, not guaranteed results. Inspect after a test section.

How do FF and SF foam pads differ?

FF refers to the flat-face profile and SF to a square-face/grooved profile. Both have cutting grades, but their working surfaces differ. Compare the actual pad construction and its stated use; neither face is automatically preferable for every surface.

What about sanding, orange peel, and glass?

Sanding and orange-peel leveling can remove clear coat and require specialized abrasives, measurement, and experience. Glass requires products designed for glass. Do not treat the manufacturer's broad application chart as proof an ordinary paint pad or compound is suitable.

Why isn't a pad removing scratches?

First check whether the defect is safely correctable. Inspect the pad for loading and verify the compound and technique on a small test area. Increase aggressiveness only when justified; deep scratches may remain.

Why do holograms or haze remain?

A heavy cutting pass may leave marring, especially on sensitive finishes. Check with a clean inspection area, then refine using a compatible finishing pad and polish where needed.

Why is the pad overheating or losing effectiveness?

Prolonged polishing, excessive pressure, and loaded pads can reduce performance and raise heat. Stop, inspect the pad and surface, clean or change the pad, and follow the tool's operating instructions.

Why does the pad slip, vibrate, or wobble?

Stop the machine. Check pad centering, backing-plate diameter, hook-and-loop condition, attachment type, and damage. Do not operate mismatched or damaged components.

Does a darker pad always cut more?

No. SPTA uses different color systems between pad series. Check the product's specific grade, number, and intended application.

Should I always begin with heavy-cut foam or wool?

No. Begin with the least aggressive combination likely to work on a small test spot. Sanding and aggressive correction are not automatically necessary.

Can I use the same pad for cutting and finishing?

Use separate clean pads for different compounds to reduce cross-contamination and maintain predictable finishing.

Which pad fits my SPTA polisher?

Check the model's supported backing plate, pad diameter, attachment system and operating instructions. Similar pad colors or machine shapes don't guarantee fitment.